How To Make A Knife Sheath? Sometimes you need an item close at hand: not in a pouch, but fairly there where you require it. A pocket watch, knife, compass, cell phone, or any other thing you do not want to follow for are all great competitors for a leather sheath knife. You might need to make something to continue a Multi-Tool or any specific tool you may need to keep able at all times. If you are a widget lover & cannot search a case for your widget, just change widget wherever it says knife.
This post is useful for the knife you executed, but also teaches the step of Wet-Shaping leather. When soaked, leather can be developed & moulded to fit various objects. In this article, we at BestDamascussKnife will give you the guide on the How To Make A Knife Sheath. Is a guide of some of the great idea out there to assist you to make a great knife sheath.
You Might Also Like ⇒
Best Pocket Knife for Kid
How To Test Knife Sharpness
How To Sharpen A Knife Without A Sharpener
Best Folding Knife Under 100
Cleaver Folding Knife
Best Japanese Knife Set
How To Make A Knife Sheath Materials & Tools
-
How To Make A Knife Sheath
Leather, Medium-Weight (5-to-6 ounces)
- Rotary-Cutter or X-Acto knife
- Pencil
- Cardboard from a file folder
- Rowel Wheel
- Fid
- Groover Tool
- Waxed Artificial Sinew or Thread
- Leather-Stitching Needles
- Pie-Pan of water
- Spring Clips
- Saran Wrap
- Tape
- Dishtowel
How to Make a Leather Knife Sheath: Step By Step
How to Make a Leather Knife Sheath
1. Draw Your Pattern
How To Make A Knife Sheath? Lay the edge out on your part of roughly trace & cardboard around the knife blade & as much of the designation as you need to cover with your knife sheath. The pattern isn’t balanced, as the back of the knife sheath has an expansion that eventually will be folded down & joined in place to create a loop through which your zone will be attached. Again, this does not have to be accurate, & better too small than too large.
2. Cut Out & Assemble Your Pattern
Using a set of scissors, do a rigid cut to see how your design looks when the knife is laid out.
If you are happy with it, fold the design in half on the line that will make the back of the knife blade kind of the Sheath & Trim the overlap so the design is symmetrical. Push the record against the knife blade to see where it lies inside the pattern. You can view in the photo a sparse crease in the cardboard, which shows lots of clearance btw the edge of the cardboard & the knife blade.
Next, use a tiny bit of sticky tape to make the design the same 3-dimensional knife shape as your leather will be. This enables you to create changes now while it’s easier. You can view that I have scraped back the knife pattern to even it out & give the handle a little more publicity. A little more cutting & we will be ready to make out the actual leather knife leather. Cut the tape-holding your knife pattern together, & flatten it out.
3. Trace & Cut Your Piece of Leather
How To Make A Knife Sheath? Trace your knife pattern onto the opposite side of the leather. This is because (A) it’s easier & (B) it sets up the belt-loop so the best side is facing ahead. I tend to neglect the belt-loop section of the knife pattern & use it just as a reviews & guide to tracing a long piece using a leader to make assured it’s long sufficient & straight.
Cut out your leather knife sheath using a Rotary-Cutter, but don’t cut into the inside edges where the knife blade portion of the sheath satisfies the belt-loop, as you will Over-Cut & make unsightly nicks. Stop little of those spots & use an X-Acto or sharp knife blade to finish the cuts.
4. Start Forming The Leather
Wrap whatever your thing is in Plastic-Wrap, using lots of it, & tape to tuck everything in perfectly.
Assemble your Dish-Towel, item to be covered, a pan of Hot-Tap water, & your Spring-Clips. Place the sheath kind of your leather in the Hot-Water. It will change colour & bubble a little as the Water-Seeps into the leather. Just several minutes is plenty.
Place your leather on the Dish-Towel & cover the towel over on the leather & push down to pat it dry & pinch out the Excess-Water. Place the knife blade on your leather & cover it over, forming it over the knife handle as you go. Using Spring-Clips, clamp the leather in place & serve the leather so it forms directly around the handle & blade.
You can make the leather with your thumbs so it holds the handle. Set it out to dry, but I normally check it every 5 minutes for the first half-hour to make assured the leather is moulding the way I need it to. You can serve with your leather again after many hours or leave it overnight. When the leather is flat, remove the Spring-Clips & you will be left with a sheath “Husk.”
5. Trim The Sheath & Prepare To Stitch The Seam
How To Make A Knife Sheath? Using the Rotary-Cutter, trim the sheath to the area by taking off the rigid edges & following the shape of the handle & blade. You are cutting through 2 layers of leather that have been Water-Hhardened so it will take a tiny more pressure. Go slow & do not cut yourself.
Using a Leather-Gouge, cut a Shallow-Groove into the leather following the edge of the Sheath-Seam. You can do this freehand or utilise a gouge with a Built-In guide. Mark, your stitches in the crease using a Rowel-Tool. 6 holes per inch is fine. If you do not have a Rowel-Tool, you can do it freehand & go slow also careful-like.
Place your sheath on a Plastic-Cutting board & using your fid, found holes in the sections you created with your Rowel-Tool. Use a small mallet & tap your Fid-Lightly. Once you have pushed all your holes, lift the top knife layer of the sheath & do the same point on the bottom, as your fid will have caused holes on the Bottom-Layer too. Make assured they line-up or your stitching willn’t be fun. If you don’t have a fid, you can utilise an Ice-Pick or other pointy stuff. Fids work a Little-Better because they make a tiny slit, not a hole.
6. Sew The Belt Loop in Place
How To Make A Knife Sheath? It’s much more comfortable to sew the Belt-Loop now before joining up the sheath. Fold your Belt-Flap over to the front & adjust it so it’s the size you need, & trim it to size. It should hold just below the head of the sheath. Any deeper & you may run into difficulties with the handle not seating well in the knife sheath.
Using your 4-prong punch, make a row of cells in both the end of the Belt-Loop & the top of the cover as shown. If you do not have a leather knife sheath, you can utilise a fid or Ice Pick or anything sharp & pointy. Trim excess leather knife sheath, if any, off the end of the leash. Using your pointer & artificial sinew, join the loop, going in & out unto you have 3 stitches giving. Tie off your ribbon & cut your Sinew-Close to the knot.
7. Sew The Seam
Using a Single-Needle & sinew, start-sewing from the base of the piece near the head of the sheath. Stitch the view going up into the leather & down into the next hole. You could use a double-needle method here, but for such a Short-Seam, a Single-Needle method is fine.
Once you join the tip of your knife sheath, turn around & go up from the floor, doing the reverse of what you just made. The effect is to produce a stitch that will not unravel, & with the groove in the cover, the tape is defended & Sits-Flush or below the area of the leather. Tie off your clumps, then thread your pin in & out the End-Holes a few periods, finishing by attaching the pin through one-layer of leather & then pull snug. Cut the Lacing-Flush with the seam & it will be stored.
Using the Wooden-End of your fid, polish the seam of your cover to even out the punch & stitching the stitches falling into the knife sheath.
8. Insert Knife or Other Object
How To Make A Knife Sheath, Insert your knife. It should be simply a bit snug, it will release just a Little-Bit over time. Put it on your area. Revel in the awareness you made something excellent.
Best Knife Sheath